, , , ,

Industrial Brushless Servo S9200TTL 250kg (24.5 N·m) 30V 405g TTL

XQ-POWER XQ-S9200TTL
250 kg·cm peak stall torque at 30 V · 0.13 s/60° · 405 g · TTL TTL serial, 500–2500 µs position scale
Brushless motor, steel gears, 5 ball bearings, CNC aluminium case
64 × 33 × 88.5 mm · splash-proof, customizable

Need a different torque, travel or connector? The engineering team answers against your numbers.

XQ-S9200TTL — 250 kg·cm (24.5 N·m) with a TTL serial input, for a controller board inside the machine A brushless motor drives a steel train onto a 25T, φ11.8 mm output in five ball bearings, inside a 64 × 33 × 88.5 mm machined aluminium case at 405 g. The input stage is TTL serial: the command comes from a control board in the same enclosure as the joint, over a short lead, with no transceiver between the two.

The unit gives 200 kg·cm on 24 V, 230 kg·cm on 28 V and 250 kg·cm on 30 V, with speed and current at all three rails. Rated and tested to inspection specification X9_9200.03, dated 2023-08-01.

Peak stall torque250 kg·cmat 30 V · 3471.9 oz-in · 24.5 N·m Speed0.13 s/60°at 30 V · 0.20 s at 28 V Supply24–30 Vthree published points
ControlTTLTTL serial · 360° across 1000–2000 µs Envelope64 × 33 × 88.5 mm86.0 mm across the ears · 25T-φ11.8 Mass405 g5 ball bearings · no mechanical stop

Is the XQ-S9200TTL the right servo for your joint?

A TTL input suits a machine that keeps its own controller next to the joint. No transceiver, no bus segment to plan: three wires from the board to the socket, and the board owns the timing. This is the build for a purpose-built machine whose electronics are inside the same enclosure as the mechanism.

Travel is 360° across the 1000–2000 µs span and section 3-4 reads No Limit. The joint goes where the board tells it and the machine provides the end positions.

Specify this unit when

  • The controller is a board inside the machine, close to the joint
  • The lead from board to servo is short and stays inside the enclosure
  • The move needs the better part of a full turn
  • The rail holds 24–30 V under load
  • The joint can use a 25T, φ11.8 mm spline

Specify a different unit when

  • The controller is in a cabinet some metres away
  • Several joints have to be dropped from one port
  • The axis depends on an internal stop
  • The joint needs more than 250 kg·cm
  • The machine runs a 6–8.4 V rail

Torque and speed at 24, 28 and 30 Volts

Rows 4-1 to 4-13, three rails, locked-shaft figures. TTL changes the wire count between the board and the joint and leaves the torque column alone.

Supply Peak stall torque No-load speed No-load current Stall current
24 V 200.0 kg·cm 0.29 s/60° 200 mA 5.5 A
28 V 230.0 kg·cm 0.20 s/60° 300 mA 7 A
30 V 250.0 kg·cm 0.13 s/60° 400 mA 8 A

250 kg·cm at 30 V with 0.13 s per 60°, 230 kg·cm at 28 V and 200 kg·cm at 24 V. The rail sets both numbers by a wider margin than any interface choice does, so the supply belongs in the joint specification.

No-load current 200 to 400 mA. Stall is 5.5 A at 24 V, 7 A at 28 V, 8 A at 30 V. On a TTL build the signal pair is short and the power pair is not, so the gauge and the length of the supply lead are what the installer has to get right.

Fit: envelope, spline and mass

64 × 33 × 88.5 mm, 86.0 mm across the ears, 5.00 mm ear thickness with Ø6 holes. Height is 103.85 mm to the top of the spline and 94.05 mm to the case line, so the clearance has to be cut for the shaft, above the body line.

25T at φ11.8 mm with a metal arm supplied. The spline is heavier than the 40 mm frames carry, which is what lets the output take 250 kg·cm without a support bearing on the arm.

405 g. On a moving axis that is mass the drive accelerates every cycle, and this frame carries 250 kg·cm at the lowest weight we build it.

Drive, current and heat

8 A at stall on 30 V, 400 mA at no load. The supply lead is where this build loses performance: a long thin pair drops volts at 8 A, and the joint that starts at 30 V and arrives at 26 V behaves like a 28 V unit at 230 kg·cm.

Dead band 3 µs, neutral 1500 µs, window 500–2500 µs, all customizable. The board works in these units directly, so the resolution it can command is the dead band and the centre it assumes is the neutral figure.

Fins cover the motor section and the drive is mounted against them. 8 A in a sealed 405 g case is a heat budget: section 2-2 puts the operating limit at 60 ℃, and a joint holding a load without moving sits near stall current while it does.

Five bearings on a φ11.8 mm output. A rigid arm runs unsupported at this torque; a long arm still wants an outboard bearing, because the bearings carry torque and the bending load at the end of a lever is a separate case.

Sealing and environment

Section 3-11 records splash resistance as Yes on a machined aluminium case with sealed joint faces. A higher water-protection grade is built to order, with the class and the test standard agreed at order stage.

The socket is outside the sealed volume and on a TTL build it sits next to the signal wires. Keep the plug dry or seal it to the same standard, and route the lead down and away from the socket.

−30 ℃ to 60 ℃ operating, −30 ℃ to 70 ℃ storage. The top of the range is the figure to check on a joint that holds torque stationary, because the case is sealed and the fins are the only path out.

Full specification

The complete sheet for the XQ-S9200TTL, in the order it appears on inspection document X9_9200.03, dated 2023-08-01: measured figures throughout, and where we have none the row says so.

Model XQ-S9200TTL
Peak stall torque (SI) 24.5 N·m at 30 V
Voltage range 24–30 V
Control interface TTL serial
Amplifier Digital controller
Rotating direction CCW (1000–2000 µs), customizable
Angle of limit None, no mechanical stop
Motor Brushless
Gear train Steel
Bearing system 5 ball bearings
Output spline 25T, φ11.8 mm
Horn supplied Metal arm supplied
Case Aluminium CNC, all-metal case
Dimensions 64 × 33 × 88.5 mm
Weight 405 g
Cable length Socket only; mating lead supplied separately
Operating temperature −30 ℃ to 60 ℃
Storage temperature −30 ℃ to 70 ℃
Sealing Splash-proof · higher water-protection grade built to order
Specification revision X9_9200.03, dated 2023-08-01

Download the XQ-S9200TTL datasheet (PDF)

The inspection sheet for this model, including the dimensional drawing and the control-signal table, is available as a PDF.

XQ-S9200TTL inspection specification
Revision X9_9200.03 · dated 2023-08-01 · PDF
Download PDF

If you need the drawing in DWG, a STEP model, or the control-signal table as a separate sheet, tell us which format your CAD system uses and we will send that instead.

Variants, samples and OEM work

The pulse build is S9200D, the CAN build S9200DC and the Modbus build RS9200MB. The 700 kg·cm side-mount unit with the same input is S9450FTTL.

Four input stages share this frame: pulse, CAN, RS485 Modbus and TTL. All four use the same bracket, the same 25T φ11.8 mm output and the same 360° figure, so the choice comes down to what the controller speaks.

For OEM and ODM work on the XQ-S9200TTL we start from five numbers: the torque you need at your speed, the supply you actually run, the interface your controller speaks, the envelope the joint allows, and the duty cycle. Send those and we answer one of three ways — the XQ-S9200TTL covers it as stock at 250 kg·cm, a build of the same 64 × 33 × 88.5 mm frame does, or the axis needs a different frame. Send the XQ-S9200TTL numbers to the engineering team.

Quick facts and cross-reference

The rows below are what to quote for the XQ-S9200TTL: 250 kg·cm (24.5 N·m) on 24–30 V with TTL input, plus the two makes buyers usually weigh it against.

Model XQ-S9200TTL
Peak stall torque 250 kg·cm · 24.5 N·m at 30 V
Voltage range 24–30 V
Control interface TTL serial
Speed 0.13 s/60°
Mass / envelope 405 g · 64 × 33 × 88.5 mm
Also described as serial bus servo, daisy-chain servo, smart servo, bus actuator

Buyers often arrive here from a DSpower DS-R009D or a Waveshare RSBL120-24, which are built around 24 V industrial rails with a bus interface; the XQ-S9200TTL is 250 kg·cm (24.5 N·m) on 24–30 V, so put the two on the same rail and in the same unit before comparing torque.

Cross-reference DSpower DS-R009D, Waveshare RSBL120-24
Their typical rail built around 24 V industrial rails with a bus interface
This model 250 kg·cm (24.5 N·m) on 24–30 V, TTL input

FAQ

What logic level does the TTL input expect?

The sheet specifies the command signal as TTL. The level your board drives and the frame it sends are agreed at order stage and written into the protocol note that ships with the unit. Tell us the board and its output stage and we confirm the match in writing before the order.

How long can the TTL lead be?

Keep it short and inside the enclosure. A single-ended signal line picks up what the motor cables radiate, and at 8 A the supply leads are the loudest thing in the bay. Where the controller has to sit metres away, use the RS485 or CAN build of this frame.

Does it have a mechanical stop?

No. Section 3-4 reads No Limit and 5-5 gives 360° across the 1000–2000 µs span. The machine provides the end positions, and the joint drives to whatever the board asks.

What supply and current?

24 to 30 V, with 250 kg·cm at 0.13 s on 30 V and 200 kg·cm at 0.29 s on 24 V. Stall is 8 A at 30 V, 7 A at 28 V, 5.5 A at 24 V, plus 400 mA at no load. Size the supply lead on the stall current at the rail you run.

Is the lead included?

No. The case carries a socket and the mating lead is a separate purchase. Send the length, the pinout and the connector on your board and the harness is quoted with the servo.

Why is the operating limit 60 ℃?

Because 8 A stall in a 405 g sealed case leaves less margin than a 100 kg·cm build does. The limit comes from section 2-2 and it applies at the mounting point.

Is the XQ-S9200TTL a drop-in replacement for a DSpower DS-R009D?

No. The DSpower DS-R009D runs on a different rail and a different frame, while the XQ-S9200TTL is 250 kg·cm (24.5 N·m) on 24–30 V with TTL input, so a swap means checking voltage, envelope and travel first. Send the rail and envelope your machine runs and we will say whether the XQ-S9200TTL frame fits.

What should I compare before choosing between the XQ-S9200TTL and a Waveshare RSBL120-24?

Four numbers decide between the XQ-S9200TTL and a Waveshare RSBL120-24: peak stall torque in N·m, the rail you actually run, stall current, and whether your controller speaks TTL. The XQ-S9200TTL publishes 250 kg·cm (24.5 N·m) on 24–30 V; put the Waveshare RSBL120-24 on that same rail and in the same unit before you compare the two.

Model

XQ-S9200TTL

Motor

Brushless

Gear train

Steel

Bearings

5 ball bearings

Torque @ 30 V

250.0 kg·cm (3471.8 oz-in)

Torque @ 28 V

230.0 kg·cm (3194.1 oz-in)

Torque @ 24 V

200.0 kg·cm (2777.5 oz-in)

Speed @ 30 V

0.13 s/60°

Speed @ 28 V

0.20 s/60°

Speed @ 24 V

0.29 s/60°

Voltage range

24–30 V

Dimensions

64 × 33 × 88.5 mm

Weight

405 g

Output spline

25T, φ11.8 mm

Case

CNC aluminium case

Protection

Splash-proof, customizable

Communication

TTL

Request a quote for Industrial Brushless Servo S9200TTL 250kg (24.5 N·m) 30V 405g TTL
















    Scroll to Top