, , , ,

Industrial Brushless Servo RS9200MB 250kg (24.5 N·m) 30V 405g Modbus

XQ-POWER XQ-RS9200MB
250 kg·cm peak stall torque at 30 V · 0.13 s/60° · 405 g · RS485 Modbus RS485 Modbus, 500–2500 µs position scale
Brushless motor, steel gears, 5 ball bearings, CNC aluminium case
64 × 33 × 88.5 mm · splash-proof, customizable

Need a different torque, travel or connector? The engineering team answers against your numbers.

XQ-RS9200MB — 250 kg·cm (24.5 N·m) on RS485 Modbus, for axes a PLC already owns A brushless motor drives a steel train onto a 25T, φ11.8 mm output in five ball bearings, inside a 64 × 33 × 88.5 mm machined aluminium case at 405 g. The input stage is an RS485 Modbus node, so a PLC or an industrial controller addresses the joint the way it addresses a drive, over a twisted pair it already has.

Rated at 200 kg·cm on 24 V, 230 kg·cm on 28 V and 250 kg·cm on 30 V, with speed and current at each rail. Inspection sheet X9_9200.03, dated 2023-08-01, is the source for every figure here.

Peak stall torque250 kg·cmat 30 V · 3471.9 oz-in · 24.5 N·m Speed0.13 s/60°at 30 V · 0.20 s at 28 V Supply24–30 Vthree published points
ControlRS485 ModbusRS485 Modbus · 360° across 1000–2000 µs Envelope64 × 33 × 88.5 mm86.0 mm across the ears · 25T-φ11.8 Mass405 g5 ball bearings · no mechanical stop

Is the XQ-RS9200MB the right servo for your joint?

Modbus is the protocol a plant PLC already speaks, and putting a 250 kg·cm joint on it means the axis is programmed in the same environment as the rest of the machine. The register the master writes is a position; the joint travels 360° across the span and holds where it is told.

Nothing mechanical was altered for the interface: five bearings on a φ11.8 mm output, a 64 × 33 mm case, no stop inside, −30 ℃ to 60 ℃ operating. A machine drawn around the pulse build keeps its bracket, its arm and its travel figures.

Specify this unit when

  • The controller is a PLC or drive that already runs Modbus RTU
  • The joints sit on a bus segment the cabinet already owns
  • The move needs the better part of a full turn
  • The rail holds 24–30 V under load
  • The joint can use a 25T, φ11.8 mm spline

Specify a different unit when

  • There is no Modbus master on the machine and no gateway
  • The axis needs a hard stop inside the servo
  • The joint needs more than 250 kg·cm
  • The machine runs a 6–8.4 V rail
  • The bay cannot take a 64 mm wide case with a socket underneath

Torque and speed at 24, 28 and 30 Volts

Rows 4-1 to 4-13 on the same three rails. The bus does not move these numbers, and it does not move the 8 A either.

Supply Peak stall torque No-load speed No-load current Stall current
24 V 200.0 kg·cm 0.29 s/60° 200 mA 5.5 A
28 V 230.0 kg·cm 0.20 s/60° 300 mA 7 A
30 V 250.0 kg·cm 0.13 s/60° 400 mA 8 A

250 kg·cm at 30 V with 0.13 s per 60°; 230 kg·cm at 28 V; 200 kg·cm at 24 V. The rail decides both the torque and the speed, and it decides them by more than a bus interval ever will, which is why we specify on the supply that is actually there.

Stall current 5.5 A at 24 V, 7 A at 28 V, 8 A at 30 V against 200 to 400 mA at no load. On a Modbus segment the wiring is one pair, and the power is not: every node still needs its own feed sized on the stall column.

Fit: envelope, spline and mass

64 × 33 × 88.5 mm, 86.0 mm across the ears, 5.00 mm ear thickness with Ø6 holes. Height runs to 103.85 mm at the top of the spline and 94.05 mm to the case line, so the plate needs clearance for the shaft above the body line.

25T at φ11.8 mm with a metal arm supplied. This is the heaviest spline below the 700 kg·cm frame, and it is what carries 250 kg·cm into an arm without an outboard bearing.

405 g. On a gantry that mass travels with the axis on every cycle, and it is why this frame is chosen where a 700 kg·cm unit would be too heavy to move.

Drive, current and heat

8 A at stall on 30 V, 400 mA at no load. A long pair drops voltage, and the joint that starts at 30 V and arrives at 26 V behaves like a 28 V unit: 230 kg·cm at 0.20 s.

Dead band 3 µs, neutral 1500 µs, window 500–2500 µs, all customizable. On Modbus these are the resolution and the centre point of the position value the master writes, so they sit in the commissioning record with the slave address and the line settings.

Fins cover the motor section and the drive sits on them. 8 A in a sealed 405 g case is a heat budget with a ceiling: section 2-2 puts the operating limit at 60 ℃, and a joint holding a load stationary spends its time near stall current.

Five bearings on the output. A rigid arm at 250 kg·cm runs without outboard support on this frame; a long arm still wants the support, because bearings carry torque and the bending load is separate.

Sealing and environment

Section 3-11 records splash resistance as Yes, on a machined aluminium case with sealed joint faces. A higher water-protection grade is built to order, and the class and test standard are agreed at order stage.

The socket is outside the sealed volume, so the plug on the harness is the part to protect. Keep it dry or seal it to the same standard, and dress the harness downward from the socket.

−30 ℃ to 60 ℃ operating, −30 ℃ to 70 ℃ storage. The upper limit is the one to watch on a joint holding torque without moving, because a sealed case has no airflow and the fins are the only path out.

Full specification

The complete sheet for the XQ-RS9200MB, in the order it appears on inspection document X9_9200.03, dated 2023-08-01: measured figures throughout, and where we have none the row says so.

Model XQ-RS9200MB
Peak stall torque (SI) 24.5 N·m at 30 V
Voltage range 24–30 V
Control interface RS485 Modbus
Amplifier Digital controller
Rotating direction CCW (1000–2000 µs), customizable
Angle of limit None, no mechanical stop
Motor Brushless
Gear train Steel
Bearing system 5 ball bearings
Output spline 25T, φ11.8 mm
Horn supplied Metal arm supplied
Case Aluminium CNC, all-metal case
Dimensions 64 × 33 × 88.5 mm
Weight 405 g
Cable length Socket only; mating lead supplied separately
Operating temperature −30 ℃ to 60 ℃
Storage temperature −30 ℃ to 70 ℃
Sealing Splash-proof · higher water-protection grade built to order
Specification revision X9_9200.03, dated 2023-08-01

Download the XQ-RS9200MB datasheet (PDF)

The inspection sheet for this model, including the dimensional drawing and the control-signal table, is available as a PDF.

XQ-RS9200MB inspection specification
Revision X9_9200.03 · dated 2023-08-01 · PDF
Download PDF

If you need the drawing in DWG, a STEP model, or the control-signal table as a separate sheet, tell us which format your CAD system uses and we will send that instead.

Variants, samples and OEM work

The pulse build is S9200D, the CAN build S9200DC and the TTL build S9200TTL. The 700 kg·cm side-mount unit on the same protocol is RS9450FMB.

Four input stages are offered on this frame — pulse, CAN, RS485 Modbus and TTL — and all of them share the bracket, the arm and the 360° figure. The interface is a line on the quotation.

For OEM and ODM work on the XQ-RS9200MB we start from five numbers: the torque you need at your speed, the supply you actually run, the interface your controller speaks, the envelope the joint allows, and the duty cycle. Send those and we answer one of three ways — the XQ-RS9200MB covers it as stock at 250 kg·cm, a build of the same 64 × 33 × 88.5 mm frame does, or the axis needs a different frame. Send the XQ-RS9200MB numbers to the engineering team.

Quick facts and cross-reference

The rows below are what to quote for the XQ-RS9200MB: 250 kg·cm (24.5 N·m) on 24–30 V with RS485 input, plus the two makes buyers usually weigh it against.

Model XQ-RS9200MB
Peak stall torque 250 kg·cm · 24.5 N·m at 30 V
Voltage range 24–30 V
Control interface RS485 Modbus
Speed 0.13 s/60°
Mass / envelope 405 g · 64 × 33 × 88.5 mm
Also described as RS485 servo, Modbus servo, RS-485 bus actuator, daisy-chain actuator

Buyers often arrive here from a DSpower DS-R009D or a Waveshare RSBL120-24, which are built around 24 V industrial rails with a bus interface; the XQ-RS9200MB is 250 kg·cm (24.5 N·m) on 24–30 V, so put the two on the same rail and in the same unit before comparing torque.

Cross-reference DSpower DS-R009D, Waveshare RSBL120-24
Their typical rail built around 24 V industrial rails with a bus interface
This model 250 kg·cm (24.5 N·m) on 24–30 V, RS485 input

FAQ

What slave address and baud rate does it ship with?

Section 5-1 names RS485 Modbus. Address, baud rate, parity and the register map are set at order stage against your master, written into the protocol note that ships with the unit, and confirmed in writing before the order is accepted. Give us the values your program expects and we set them at the factory.

Can it share the segment with drives and meters?

It can, and the segment has to be planned like any other. RS485 allows 32 unit loads; the joint is one. Keep the pair away from motor cables, terminate at both physical ends and check the line with every node connected before commissioning.

What travel does the sheet give?

360° across the 1000–2000 µs span in section 5-5, with section 3-4 reading No Limit. Movement beyond a full turn depends on the control arrangement you order, so send the motion profile and we confirm it in writing.

How do I size the power feed?

On the stall column for the nodes that can load together: 8 A at 30 V, 7 A at 28 V, 5.5 A at 24 V, plus 400 mA each at no load. The bus is one pair; the power is not shared.

Is a lead included?

No. The case carries a socket and the mating lead is supplied separately. Length, pinout and connector are quoted with the servo once you tell us what the controller uses.

What is the operating temperature limit?

−30 ℃ to 60 ℃ from section 2-2, and −30 ℃ to 70 ℃ storage from 2-1. At 8 A stall the case is the constraint, so measure at the mounting point.

Is the XQ-RS9200MB a drop-in replacement for a DSpower DS-R009D?

No. The DSpower DS-R009D runs on a different rail and a different frame, while the XQ-RS9200MB is 250 kg·cm (24.5 N·m) on 24–30 V with RS485 input, so a swap means checking voltage, envelope and travel first. Send the rail and envelope your machine runs and we will say whether the XQ-RS9200MB frame fits.

What should I compare before choosing between the XQ-RS9200MB and a Waveshare RSBL120-24?

Four numbers decide between the XQ-RS9200MB and a Waveshare RSBL120-24: peak stall torque in N·m, the rail you actually run, stall current, and whether your controller speaks RS485. The XQ-RS9200MB publishes 250 kg·cm (24.5 N·m) on 24–30 V; put the Waveshare RSBL120-24 on that same rail and in the same unit before you compare the two.

Model

XQ-RS9200MB

Motor

Brushless

Gear train

Steel

Bearings

5 ball bearings

Torque @ 30 V

250.0 kg·cm (3471.8 oz-in)

Torque @ 28 V

230.0 kg·cm (3194.1 oz-in)

Torque @ 24 V

200.0 kg·cm (2777.5 oz-in)

Speed @ 30 V

0.13 s/60°

Speed @ 28 V

0.20 s/60°

Speed @ 24 V

0.29 s/60°

Voltage range

24–30 V

Dimensions

64 × 33 × 88.5 mm

Weight

405 g

Output spline

25T, φ11.8 mm

Case

CNC aluminium case

Protection

Splash-proof, customizable

Communication

RS485 Modbus

Request a quote for Industrial Brushless Servo RS9200MB 250kg (24.5 N·m) 30V 405g Modbus
















    Scroll to Top