XQ-S9200DC — 250 kg·cm (24.5 N·m) as a CAN node, on the heaviest spline we build below the 700 kg·cm frame A brushless motor drives a steel train onto a 25T, φ11.8 mm output in five ball bearings, inside a 64 × 33 × 88.5 mm machined aluminium case weighing 405 g. The input stage is a CAN node: the command arrives as a frame and the joint travels 360° across the 1000–2000 µs span the sheet publishes.
The unit gives 200 kg·cm on 24 V, 230 kg·cm on 28 V and 250 kg·cm on 30 V, with speed and current at each rail. Rated and tested to inspection specification X9_9200.03, dated 2023-08-01.
| Peak stall torque250 kg·cmat 30 V · 3471.9 oz-in · 24.5 N·m | Speed0.13 s/60°at 30 V · 0.20 s at 28 V | Supply24–30 Vthree published points |
| ControlCANCAN bus · 360° across 1000–2000 µs | Envelope64 × 33 × 88.5 mm86.0 mm across the ears · 25T-φ11.8 | Mass405 g5 ball bearings · no mechanical stop |
Is the XQ-S9200DC the right servo for your joint?
This is the frame for an axis that carries real load and has to arrive with other axes. 250 kg·cm on a φ11.8 mm spline, 405 g, and a CAN node so the master schedules the frames for the whole set of axes. Arbitration gives the joint that has to arrive first its slot ahead of the traffic that can wait.
Travel is 360° across 1000–2000 µs and section 3-4 reads No Limit. A joint with a full turn and no stop covers a rotating axis or a joint whose working arc is a segment of that turn, and it takes its end positions from the machine.
Specify this unit when
- The machine runs a CAN bus and the master addresses nodes
- The joint has to arrive in step with other axes on the same bus
- The move needs the better part of a full turn
- The rail holds 24–30 V under load
- The joint can use a 25T, φ11.8 mm spline
Specify a different unit when
- The controller has no CAN port or gateway
- The mechanism depends on the servo to find its end stops
- The joint needs more than 250 kg·cm
- The machine runs a 6–8.4 V rail
- The bay cannot take a 64 mm wide case with a socket underneath
Torque and speed at 24, 28 and 30 Volts
Rows 4-1 to 4-13: locked-shaft torque, no-load speed, no-load current and stall current on three rails. The bus changes where the command comes from and leaves this table untouched.
| Supply | Peak stall torque | No-load speed | No-load current | Stall current |
|---|---|---|---|---|
| 24 V | 200.0 kg·cm | 0.29 s/60° | 200 mA | 5.5 A |
| 28 V | 230.0 kg·cm | 0.20 s/60° | 300 mA | 7 A |
| 30 V | 250.0 kg·cm | 0.13 s/60° | 400 mA | 8 A |
250 kg·cm at 30 V and 0.13 s per 60°, 230 kg·cm at 28 V, 200 kg·cm at 24 V. The speed more than doubles across the rail, 0.29 s to 0.13 s, so a machine running on a 24 V battery behaves nothing like one on a regulated 30 V supply.
Stall current is 5.5 A at 24 V, 7 A at 28 V and 8 A at 30 V, against 200 to 400 mA at no load. Four of these loading together on one feed is 32 A at 30 V. On a bus the sum of the stall currents is what decides how the machine is wired.
Fit: envelope, spline and mass
64 × 33 × 88.5 mm, 86.0 mm across the mounting ears, 5.00 mm of ear thickness and Ø6 holes. Overall height from the base to the top of the spline is 103.85 mm, with 94.05 mm to the top of the case. Check the height before the plate is cut, because the shaft sits above the body line.
25T at φ11.8 mm with a metal arm supplied. The spline is larger than the 40 mm frames carry, so an arm from a smaller build needs machining to seat, and the load path through the output is sized for 250 kg·cm.
405 g. On a moving axis that is mass the drive accelerates every cycle, and it is the reason this frame is used on gantries where a 700 kg·cm unit would be too much weight to move.
Drive, current and heat
8 A at stall on 30 V, 400 mA at no load. The rail is doing the work: at 24 V the same joint pulls 5.5 A for 200 kg·cm, and a feed that sags to 26 V under load hands the joint the 28 V column at 230 kg·cm.
Dead band 3 µs, neutral 1500 µs, window 500–2500 µs, all marked customizable. On the bus these become the smallest position step the master can command and the point the joint treats as zero, so they belong in the commissioning notes beside the node identifier.
The case is machined with fins over the motor section and the drive sits against them. At 8 A stall the heat is real: a joint that holds a load without moving sits near stall current for as long as the load is there, and the fins and the bracket are the only path out.
Five bearings on a φ11.8 mm output. That is enough for a rigid arm at this torque, and it is the reason the unit runs an arm without outboard support. Where the arm is long, support it anyway: bearings take torque, and a bending moment is a different load.
Sealing and environment
Section 3-11 records splash resistance as Yes. The case is machined aluminium with sealed joint faces and a sealed output, which covers a wash-down bay or an enclosure that sees spray. A higher water-protection grade is built to order, with the class and the test standard agreed at order stage.
The case carries a socket, so the plug on the harness sits outside the sealed volume. Keep that plug dry or seal it to the same standard, and dress the harness down and away from the socket so water leaves the joint.
Operating range −30 ℃ to 60 ℃, storage −30 ℃ to 70 ℃. The top end is lower than the pulse build on this frame for the same reason the body is heavier: more torque in the same envelope means more heat, and a sealed aluminium case has no airflow through it.
Full specification
The complete sheet for the XQ-S9200DC, in the order it appears on inspection document X9_9200.03, dated 2023-08-01: measured figures throughout, and where we have none the row says so.
| Model | XQ-S9200DC |
| Peak stall torque (SI) | 24.5 N·m at 30 V |
| Voltage range | 24–30 V |
| Control interface | CAN bus |
| Amplifier | Digital controller |
| Rotating direction | CCW (1000–2000 µs), customizable |
| Angle of limit | None, no mechanical stop |
| Motor | Brushless |
| Gear train | Steel |
| Bearing system | 5 ball bearings |
| Output spline | 25T, φ11.8 mm |
| Horn supplied | Metal arm supplied |
| Case | Aluminium CNC, all-metal case |
| Dimensions | 64 × 33 × 88.5 mm |
| Weight | 405 g |
| Cable length | Socket only; mating lead supplied separately |
| Operating temperature | −30 ℃ to 60 ℃ |
| Storage temperature | −30 ℃ to 70 ℃ |
| Sealing | Splash-proof · higher water-protection grade built to order |
| Specification revision | X9_9200.03, dated 2023-08-01 |
Download the XQ-S9200DC datasheet (PDF)
The inspection sheet for this model, including the dimensional drawing and the control-signal table, is available as a PDF.
|
XQ-S9200DC inspection specification Revision X9_9200.03 · dated 2023-08-01 · PDF |
Download PDF |
If you need the drawing in DWG, a STEP model, or the control-signal table as a separate sheet, tell us which format your CAD system uses and we will send that instead.
Variants, samples and OEM work
The pulse build of this frame is S9200D; the Modbus and TTL builds are RS9200MB and S9200TTL. The lighter CAN frame below it is S9080FC and the 700 kg·cm side-mount unit is S9450FC.
The 9-series frames share the same command scale and the same no-stop arrangement, so a machine that grows from 100 to 250 kg·cm keeps its controller configuration and changes the mount and the harness.
For OEM and ODM work on the XQ-S9200DC we start from five numbers: the torque you need at your speed, the supply you actually run, the interface your controller speaks, the envelope the joint allows, and the duty cycle. Send those and we answer one of three ways — the XQ-S9200DC covers it as stock at 250 kg·cm, a build of the same 64 × 33 × 88.5 mm frame does, or the axis needs a different frame. Send the XQ-S9200DC numbers to the engineering team.
Quick facts and cross-reference
The rows below are what to quote for the XQ-S9200DC: 250 kg·cm (24.5 N·m) on 24–30 V with CAN input, plus the two makes buyers usually weigh it against.
| Model | XQ-S9200DC |
| Peak stall torque | 250 kg·cm · 24.5 N·m at 30 V |
| Voltage range | 24–30 V |
| Control interface | CAN bus |
| Speed | 0.13 s/60° |
| Mass / envelope | 405 g · 64 × 33 × 88.5 mm |
| Also described as | CAN bus servo, CAN actuator, CANopen servo, robot joint actuator |
Buyers often arrive here from a DSpower DS-R009D or a Waveshare RSBL120-24, which are built around 24 V industrial rails with a bus interface; the XQ-S9200DC is 250 kg·cm (24.5 N·m) on 24–30 V, so put the two on the same rail and in the same unit before comparing torque.
| Cross-reference | DSpower DS-R009D, Waveshare RSBL120-24 |
| Their typical rail | built around 24 V industrial rails with a bus interface |
| This model | 250 kg·cm (24.5 N·m) on 24–30 V, CAN input |
FAQ
How many degrees does the S9200DC turn?
Section 5-5 gives 360° across the 1000–2000 µs span, and section 3-4 reads No Limit. What the joint does beyond one turn depends on the control arrangement you order, so tell us the motion profile and we confirm the answer in writing before the order.
What bus settings do I need?
The sheet specifies the command signal as CAN. Baud rate, node identifier and frame layout are set at order stage against your master, written into the protocol note that ships with the unit, and confirmed before the order is accepted.
Why is the operating temperature 60 ℃ on this frame?
Because 8 A stall in a 405 g sealed case leaves less margin than a 100 kg·cm build does. The unit is rated −30 ℃ to 60 ℃ operating from section 2-2 of the sheet, and a joint that holds torque while stationary is the case that reaches the limit first.
Is a lead included?
No. The case carries a socket and the mating lead is supplied separately. Send us the length, the pinout and the connector your controller uses and the harness is quoted with the servo.
What should the power feed be rated at?
Size it on the stall current of the nodes that can stall at the same moment: 8 A at 30 V, 7 A at 28 V, 5.5 A at 24 V, plus 400 mA at no load. Four joints loading together is 32 A at 30 V, and that number decides the cable and the supply.
Will my existing arm fit?
It fits if it is cut for a 25T spline at φ11.8 mm. A horn from a 40 mm case servo has a smaller spline and will not seat. A metal arm to this spline comes with the unit.
Is the XQ-S9200DC a drop-in replacement for a DSpower DS-R009D?
No. The DSpower DS-R009D runs on a different rail and a different frame, while the XQ-S9200DC is 250 kg·cm (24.5 N·m) on 24–30 V with CAN input, so a swap means checking voltage, envelope and travel first. Send the rail and envelope your machine runs and we will say whether the XQ-S9200DC frame fits.
What should I compare before choosing between the XQ-S9200DC and a Waveshare RSBL120-24?
Four numbers decide between the XQ-S9200DC and a Waveshare RSBL120-24: peak stall torque in N·m, the rail you actually run, stall current, and whether your controller speaks CAN. The XQ-S9200DC publishes 250 kg·cm (24.5 N·m) on 24–30 V; put the Waveshare RSBL120-24 on that same rail and in the same unit before you compare the two.






