, , ,

Industrial Brushless Servo RS9080F 100kg (9.8 N·m) 30V 290g RS485

XQ-POWER XQ-RS9080F
100 kg·cm peak stall torque at 30 V · 0.16 s/60° · 290 g · RS485 RS485, 500–2500 µs position scale
Brushless motor, steel gears, 6 ball bearings, CNC aluminium case
54 × 25 × 96 mm · splash-proof, customizable

Need a different torque, travel or connector? The engineering team answers against your numbers.

XQ-RS9080F — the 100 kg·cm (9.8 N·m) column on a two-wire RS485 bus, for joints a long way from the cabinet A brushless motor drives a steel train onto a 25T, φ7.96 mm output carried in six ball bearings, inside the same 54 × 25 × 96 mm machined aluminium column as the pulse build, 290 g with its 7075 arm. The input stage is a differential RS485 transceiver, so the command arrives as a serial frame over a twisted pair from a master that may be metres away.

Rated at 75 kg·cm on 24 V, 90 kg·cm on 28 V and 100 kg·cm on 30 V, with speed and current published at all three rails. The figures come from inspection sheet X9_9080.01, dated 2026-11-02.

Peak stall torque100 kg·cmat 30 V · 1388.7 oz-in · 9.8 N·m Speed0.16 s/60°at 30 V · 0.28 s at 24 V Supply24–30 Vthree published points
ControlRS485RS485 · ±100° on the command scale Envelope54 × 25 × 96 mm74.0 mm across the ears · 25T-φ7.96 Mass290 g6 ball bearings · no mechanical stop

Is the XQ-RS9080F the right servo for your joint?

A differential pair is the reason this build exists. Where the drive cabinet sits at the far end of a gantry and the joint hangs at the near end, a two-wire RS485 line carries the command past the motor cables and the inverter without picking up what they radiate. The transceiver is inside the case; the cable is ordinary twisted pair.

The mechanics are the S9080F parts: six bearings on a φ7.96 mm output, ears machined into a 54 × 25 mm column, a 7075 arm in the box, no stop anywhere inside. The sheet gives ±100° of running degree across the 1000–2000 µs span and marks that figure customizable.

Specify this unit when

  • The controller or converter speaks RS485 over a twisted pair
  • The cabinet is some distance from the joint
  • Travel inside ±100° covers the move
  • The rail holds 24–30 V under load
  • Several units are dropped from one master port

Specify a different unit when

  • There is no RS485 port and no converter on the machine
  • The joint relies on an internal stop to hold position
  • The move needs more than ±100°
  • The machine runs a 6–8.4 V rail
  • The purchase cannot include a mating lead

Torque and speed at 24, 28 and 30 Volts

Rows 4-1 to 4-13, the same locked-shaft points as the pulse build on the same rails. The serial line changes the command path, and the torque column stays where it was.

Supply Peak stall torque No-load speed No-load current Stall current
24 V 75.0 kg·cm 0.28 s/60° 150 mA under 2 A
28 V 90.0 kg·cm 0.20 s/60° 180 mA under 2.5 A
30 V 100.0 kg·cm 0.16 s/60° 200 mA under 3 A

100 kg·cm at 30 V and 0.16 s per 60°; 90 kg·cm at 28 V; 75 kg·cm at 24 V. The 0.12 s spread between the outer rails is larger than the difference a bus interval makes, which is why we specify the joint on the rail it runs.

No-load current runs 150 to 200 mA. Stall is published as a ceiling: under 2 A at 24 V, under 2.5 A at 28 V, under 3 A at 30 V. A drop of six joints at 30 V wants under 18 A on the feed before the rest of the machine is counted, and the line voltage at the far end is what decides whether the last joint gets its 30 V.

Fit: envelope, spline and mass

54 × 25 × 96 mm, 74.0 mm across the ears, 4.0 mm ear thickness. The bracket holds the column at the top, next to the output, and the body hangs free, so the mounting plate decides how much of the case is exposed to the air.

25T at φ7.96 mm with the 7075 aluminium arm. The spline is big enough that the arm needs no outboard bearing at 100 kg·cm, and the arm comes with the unit on this frame.

290 g with the arm fitted. Where the joint travels with the axis, that is 290 g the drive has to accelerate and stop on every cycle, and it is the lightest 100 kg·cm we build.

Drive, current and heat

Under 3 A at 30 V stall, 200 mA at no load. The rail sets the current: a long twisted pair drops voltage under load, and a joint that starts at 30 V and arrives at 26 V behaves like a 28 V joint with 90 kg·cm and a slower 0.20 s move.

Dead band 3 µs, neutral 1500 µs, window 500–2500 µs, all customizable. Over a serial line these are the resolution and the centre point the master works in, so they go into the commissioning sheet with the address and the line settings.

The motor section sits under fins machined into the column, and 3 A is a light load for a 290 g aluminium body at ordinary duty. Heat becomes the question when the joint holds a load without moving, because the current then sits near stall and the only path out is the fins and the bracket.

Six bearings carry the output, which is what lets an unsupported arm run at this torque. On a long arm add the outboard support anyway: the bearings take torque, and the bending load at the end of a lever is a separate problem.

Sealing and environment

Section 3-11 records splash resistance as Yes. The case is one machined billet with sealed joint faces, which covers a wash-down bay or an outdoor enclosure. A higher water-protection grade is built to order, with the sealing method and test agreed at order stage.

The J30J connector sits outside the sealed volume. Keep the mating plug dry or seal it to the same standard, and route the lead downward from the entry so water runs off the joint.

Operating range −30 ℃ to 65 ℃, storage −30 ℃ to 70 ℃. The upper end is a real constraint on a joint that holds torque while stationary, because there is no airflow through a sealed aluminium column.

Full specification

The complete sheet for the XQ-RS9080F, in the order it appears on inspection document X9_9080.01, dated 2026-11-02: measured figures throughout, and where we have none the row says so.

Model XQ-RS9080F
Peak stall torque (SI) 9.8 N·m at 30 V
Voltage range 24–30 V
Control interface RS485
Amplifier Digital controller
Rotating direction CCW (1000–2000 µs), customizable
Angle of limit None, no mechanical stop
Motor Brushless
Gear train Steel
Bearing system 6 ball bearings
Output spline 25T, φ7.96 mm
Horn supplied 7075 aluminium CNC arm supplied
Case Aluminium CNC, all-metal case
Dimensions 54 × 25 × 96 mm
Weight 290 g
Cable length J30J-9TJL connector, lead purchased separately
Operating temperature −30 ℃ to 65 ℃
Storage temperature −30 ℃ to 70 ℃
Sealing Splash-proof · higher water-protection grade built to order
Specification revision X9_9080.01, dated 2026-11-02

Download the XQ-RS9080F datasheet (PDF)

The inspection sheet for this model, including the dimensional drawing and the control-signal table, is available as a PDF.

XQ-RS9080F inspection specification
Revision X9_9080.01 · dated 2026-11-02 · PDF
Download PDF

If you need the drawing in DWG, a STEP model, or the control-signal table as a separate sheet, tell us which format your CAD system uses and we will send that instead.

Variants, samples and OEM work

The pulse version is S9080F and the CAN version S9080FC. On the 250 kg·cm frame the RS485 Modbus build is RS9200MB.

This frame is offered with a pulse input, a CAN node and an RS485 transceiver, all on the same bracket, arm and travel figures. Tell us at quotation which one the controller speaks and the harness is built to match.

For OEM and ODM work on the XQ-RS9080F we start from five numbers: the torque you need at your speed, the supply you actually run, the interface your controller speaks, the envelope the joint allows, and the duty cycle. Send those and we answer one of three ways — the XQ-RS9080F covers it as stock at 100 kg·cm, a build of the same 54 × 25 × 96 mm frame does, or the axis needs a different frame. Send the XQ-RS9080F numbers to the engineering team.

Quick facts and cross-reference

The rows below are what to quote for the XQ-RS9080F: 100 kg·cm (9.8 N·m) on 24–30 V with RS485 input, plus the two makes buyers usually weigh it against.

Model XQ-RS9080F
Peak stall torque 100 kg·cm · 9.8 N·m at 30 V
Voltage range 24–30 V
Control interface RS485
Speed 0.16 s/60°
Mass / envelope 290 g · 54 × 25 × 96 mm
Also described as RS485 servo, Modbus servo, RS-485 bus actuator, daisy-chain actuator

Buyers often arrive here from a Waveshare RSBL120-24 or a Feetech SM160BL, which are built around 12-24 V bus rails with an onboard driver; the XQ-RS9080F is 100 kg·cm (9.8 N·m) on 24–30 V, so put the two on the same rail and in the same unit before comparing torque.

Cross-reference Waveshare RSBL120-24, Feetech SM160BL
Their typical rail built around 12-24 V bus rails with an onboard driver
This model 100 kg·cm (9.8 N·m) on 24–30 V, RS485 input

FAQ

Does the RS9080F speak Modbus?

Section 5-1 of the inspection sheet names RS485 for this model and nothing above it. The frame layout and command set are ours, documented in the protocol note that ships with the unit and agreed with you before the order. Where a master runs Modbus RTU, the 250 kg·cm frame carries it as RS9200MB.

How long a cable can I run?

The limit is the transceiver at the master and the environment the pair runs through. RS485 is specified for a thousand metres at low rate, and in a machine bay the practical figure is set by how close the pair runs to motor cables. Keep it away from the drives, terminate at both ends, and check the line with the last joint connected.

Is there a stop inside the case?

No. Section 3-4 is blank and 5-5 gives ±100° across the 1000–2000 µs span. The machine has to own its limits, and at 100 kg·cm a joint driven into a hard stop will damage the mechanism before it stalls.

What supply and current should I plan for?

24 to 30 V, and the joint is specified on the rail it sees under load. Stall is under 3 A at 30 V, under 2.5 A at 28 V, under 2 A at 24 V, with 200 mA at no load. Add the nodes that can stall together and size the feed on that total.

Which end of the pair needs the termination?

Both ends of the bus, with the middle drops left open. A unit that sits at the end of the line carries the resistor; one in the middle does not. We mark the end units on the harness drawing so the installer does not have to work it out on site.

Can I use the arm I already have?

If it is cut for a 25T spline at φ7.96 mm, yes. The unit ships with a 7075 aluminium arm to that spline, and a horn from a 40 mm case servo will not seat on it.

Is the XQ-RS9080F a drop-in replacement for a Waveshare RSBL120-24?

No. The Waveshare RSBL120-24 runs on a different rail and a different frame, while the XQ-RS9080F is 100 kg·cm (9.8 N·m) on 24–30 V with RS485 input, so a swap means checking voltage, envelope and travel first. Send the rail and envelope your machine runs and we will say whether the XQ-RS9080F frame fits.

What should I compare before choosing between the XQ-RS9080F and a Feetech SM160BL?

Four numbers decide between the XQ-RS9080F and a Feetech SM160BL: peak stall torque in N·m, the rail you actually run, stall current, and whether your controller speaks RS485. The XQ-RS9080F publishes 100 kg·cm (9.8 N·m) on 24–30 V; put the Feetech SM160BL on that same rail and in the same unit before you compare the two.

Model

XQ-RS9080F

Motor

Brushless

Gear train

Steel

Bearings

6 ball bearings

Torque @ 30 V

100.0 kg·cm (1388.7 oz-in)

Torque @ 28 V

90.0 kg·cm (1249.9 oz-in)

Torque @ 24 V

75.0 kg·cm (1041.6 oz-in)

Speed @ 30 V

0.16 s/60°

Speed @ 28 V

0.20 s/60°

Speed @ 24 V

0.28 s/60°

Voltage range

24–30 V

Dimensions

54 × 25 × 96 mm

Weight

290 g

Output spline

25T, φ7.96 mm

Case

CNC aluminium case

Protection

Splash-proof, customizable

Communication

RS485

Request a quote for Industrial Brushless Servo RS9080F 100kg (9.8 N·m) 30V 290g RS485
















    Scroll to Top