XQ-S9080F — 100 kg·cm (9.8 N·m) on a 30 V rail in a 290 g column, 0.16 s per 60°, with no stop inside the case A brushless motor drives a steel train onto a 25T, φ7.96 mm output carried in six ball bearings, inside a 54 × 25 mm machined aluminium column. The ears are cut into the side of the case and a 7075 aluminium arm comes with the unit. There is no mechanical stop: the case has nothing inside it to limit travel.
We rate it at 75 kg·cm on 24 V, 90 kg·cm on 28 V and 100 kg·cm on 30 V, with speed and current at all three rails. Rated and tested to inspection specification X9_9080.01, dated 2026-11-02.
| Peak stall torque100 kg·cmat 30 V · 1388.7 oz-in · 9.8 N·m | Speed0.16 s/60°at 30 V · 0.28 s at 24 V | Supply24–30 Vthree published points |
| ControlPWM500–2500 µs · ±100° travel | Envelope54 × 25 × 96 mm74.0 mm across the ears · 25T-φ7.96 | Mass290 g6 ball bearings · no mechanical stop |
Is the XQ-S9080F the right servo for your joint?
A hundred kg·cm from 290 g is the whole argument of this build, and it is spent on bearings and structure, with a motor no larger than the case allows. Six ball bearings carry a φ7.96 mm output, and the case is a 54 × 25 mm column with the mounting ears machined into it, so the load goes into the case wall along its length.
There is no stop in the case. The inspection sheet leaves section 3-4 blank and specifies the running degree as ±100° on the command window, which means the machine has to own its own limits. A joint driven past a hard stop by a servo this strong will break something, and it will not be the servo.
Specify this unit when
- The joint needs about 90–100 kg·cm and the machine has its own stops
- Travel inside ±100° covers the move
- The supply holds 24–30 V under load
- The joint can use a 25T, φ7.96 mm spline
- The harness can be built to a J30J-9TJL connector
Specify a different unit when
- The joint depends on an internal stop to find its position
- The machine runs a 6–8.4 V rail
- The joint needs more than 100 kg·cm at 30 V
- The arm has to be a plastic or standard-size horn
- The purchase cannot include a mating lead
Torque and speed at 24, 28 and 30 Volts
Locked-shaft torque, no-load speed, no-load current and stall current at each rail, from rows 4-1 to 4-13 of the inspection sheet. The stall figures are published as ceilings.
| Supply | Peak stall torque | No-load speed | No-load current | Stall current |
|---|---|---|---|---|
| 24 V | 75.0 kg·cm | 0.28 s/60° | 150 mA | under 2 A |
| 28 V | 90.0 kg·cm | 0.20 s/60° | 180 mA | under 2.5 A |
| 30 V | 100.0 kg·cm | 0.16 s/60° | 200 mA | under 3 A |
100 kg·cm at 30 V with 0.16 s per 60°, 90 kg·cm at 28 V and 75 kg·cm at 24 V. The speed more than halves across that rail, 0.28 s to 0.16 s, so the supply is part of the joint specification and not a detail of the installation.
The stall column is written with a less-than sign: under 2 A at 24 V, under 2.5 A at 28 V and under 3 A at 30 V, against no-load current of 150 to 200 mA. Those are ceilings the inspection accepts, which is why we do not publish a thermal duty from them: the real limit is the case temperature at the mounting point.
Fit: envelope, spline and mass
54 × 25 × 96 mm, 74.0 mm across the mounting ears and 4.0 mm of ear thickness. The ears are at the top of the column, so the bracket takes the load in shear near the output and the case hangs below it. Check what sits under the case before the plate is cut.
25T at φ7.96 mm with a 7075 aluminium arm in the box. That is a large spline for a 290 g unit, and it is the reason the output takes 100 kg·cm without a support bearing on the arm.
290 g with the arm. On a moving gantry the mass at the end of the axis sets the acceleration the rest of the machine has to pay for, and this is the lightest way we build 100 kg·cm.
Drive, current and heat
Under 3 A at stall on 30 V and 200 mA at no load. The current is low for the torque because the rail is high; the number that matters is the 30 V, and a supply that sags to 26 V under load drops the joint into the 28 V column.
Dead band is 3 µs, neutral 1500 µs and the command window is 500–2500 µs, all marked customizable. The sheet gives ±100° of running degree against a blank limit field, so the travel the joint gets is the travel the machine enforces.
The case is a machined column with fins over the motor section, and at 30 V the drive runs cool in relative terms: 3 A is not a heating problem in a case this size. The joint that heats is the one holding a load against gravity with the arm stationary.
Six bearings on the output is what lets this unit take an arm with no outboard support. Where the arm is long enough to whip, add the support anyway: the bearings carry torque, and a bending moment at the end of a metre of lever is a different load.
Sealing and environment
We build the XQ-S9080F to splash-proof specification. A higher water-protection grade is built to order: name the IP class and the test standard, and we agree the cable-entry treatment for a 54 × 25 × 96 mm case before the build starts.
In a case this small the space for a gland is minimal, so the cable entry is the weak point. Route the J30J socket lead downward where the layout allows so water runs away from the entry, and seal the connector separately on any machine that is washed down or operated outdoors.
We rate the unit for −30 ℃ to 65 ℃ operating and −30 ℃ to 70 ℃ storage. The upper end interacts with the thermal budget above: a joint already near its limit at 25 ℃ has nothing left at 55 ℃.
Full specification
The complete sheet for the XQ-S9080F, in the order it appears on inspection document X9_9080.01, dated 2026-11-02: measured figures throughout, and where we have none the row says so.
| Model | XQ-S9080F |
| Peak stall torque (SI) | 9.8 N·m at 30 V |
| Voltage range | 24–30 V |
| Control interface | PWM |
| Amplifier | Digital controller |
| Rotating direction | CCW (1000–2000 µs), customizable |
| Angle of limit | None, no mechanical stop |
| Motor | Brushless |
| Gear train | Steel |
| Bearing system | 6 ball bearings |
| Output spline | 25T, φ7.96 mm |
| Horn supplied | 7075 aluminium CNC arm supplied |
| Case | Aluminium CNC, all-metal case |
| Dimensions | 54 × 25 × 96 mm |
| Weight | 290 g |
| Cable length | J30J-9TJL connector, lead purchased separately |
| Operating temperature | −30 ℃ to 65 ℃ |
| Storage temperature | −30 ℃ to 70 ℃ |
| Sealing | Splash-proof · higher water-protection grade built to order |
| Specification revision | X9_9080.01, dated 2026-11-02 |
Download the XQ-S9080F datasheet (PDF)
The inspection sheet for this model, including the dimensional drawing and the control-signal table, is available as a PDF.
|
XQ-S9080F inspection specification Revision X9_9080.01 · dated 2026-11-02 · PDF |
Download PDF |
If you need the drawing in DWG, a STEP model, or the control-signal table as a separate sheet, tell us which format your CAD system uses and we will send that instead.
Variants, samples and OEM work
This column is also built with a CAN node as S9080FC and with an RS485 transceiver as RS9080F. The next frame up is S9200D at 250 kg·cm, and the 700 kg·cm side-mount unit is S9450F. The 390 kg·cm and 700 kg·cm actuators with a different case are S9350D and S9450D.
The 9-series frames share the same command window and the same no-stop arrangement, so a machine that grows from 100 to 250 kg·cm keeps its controller settings and changes only the mount.
For OEM and ODM work on the XQ-S9080F we start from five numbers: the torque you need at your speed, the supply you actually run, the interface your controller speaks, the envelope the joint allows, and the duty cycle. Send those and we answer one of three ways — the XQ-S9080F covers it as stock at 100 kg·cm, a build of the same 54 × 25 × 96 mm frame does, or the axis needs a different frame. Send the XQ-S9080F numbers to the engineering team.
Quick facts and cross-reference
The rows below are what to quote for the XQ-S9080F: 100 kg·cm (9.8 N·m) on 24–30 V with PWM input, plus the two makes buyers usually weigh it against.
| Model | XQ-S9080F |
| Peak stall torque | 100 kg·cm · 9.8 N·m at 30 V |
| Voltage range | 24–30 V |
| Control interface | PWM |
| Speed | 0.16 s/60° |
| Mass / envelope | 290 g · 54 × 25 × 96 mm |
| Also described as | steering gear, digital servo, metal-gear servo, standard-size servo |
Buyers often arrive here from a Waveshare RSBL120-24 or a Feetech SM160BL, which are built around 12-24 V bus rails with an onboard driver; the XQ-S9080F is 100 kg·cm (9.8 N·m) on 24–30 V, so put the two on the same rail and in the same unit before comparing torque.
| Cross-reference | Waveshare RSBL120-24, Feetech SM160BL |
| Their typical rail | built around 12-24 V bus rails with an onboard driver |
| This model | 100 kg·cm (9.8 N·m) on 24–30 V, PWM input |
FAQ
Does the S9080F have a mechanical stop?
No. Section 3-4 of the inspection sheet is blank and the running degree is given as ±100° on the command window. The machine has to provide its own hard stops, and the servo drives to whatever the controller asks.
Is the lead included?
No. The unit carries a J30J-9TJL connector and the mating lead is a separate purchase. Tell us the length and the pinout your controller expects and we quote the harness with the servo.
What supply does it need?
24 to 30 V, and the joint is specified on the rail it actually runs. At 28 V it gives 90 kg·cm at 0.20 s; at 30 V, 100 kg·cm at 0.16 s. A supply that sags under load moves the joint to a lower column.
What is the stall current figure?
The sheet publishes ceilings: under 2 A at 24 V, under 2.5 A at 28 V, under 3 A at 30 V. We size the feed on the ceiling and the duty on the case temperature at the mounting point.
Will a standard arm fit?
No. The output is 25T at φ7.96 mm and the unit comes with a 7075 aluminium arm to that spline. A horn from a 40 mm case servo will not seat on it.
What is it machined from?
A single aluminium billet, all-metal case, with the mounting ears cut into the side of the column. A steel gear train and six ball bearings sit inside it.
Is the XQ-S9080F a drop-in replacement for a Waveshare RSBL120-24?
No. The Waveshare RSBL120-24 runs on a different rail and a different frame, while the XQ-S9080F is 100 kg·cm (9.8 N·m) on 24–30 V with PWM input, so a swap means checking voltage, envelope and travel first. Send the rail and envelope your machine runs and we will say whether the XQ-S9080F frame fits.
What should I compare before choosing between the XQ-S9080F and a Feetech SM160BL?
Four numbers decide between the XQ-S9080F and a Feetech SM160BL: peak stall torque in N·m, the rail you actually run, stall current, and whether your controller speaks PWM. The XQ-S9080F publishes 100 kg·cm (9.8 N·m) on 24–30 V; put the Feetech SM160BL on that same rail and in the same unit before you compare the two.






