, , ,

Industrial Brushless Servo S9080FC 100kg (9.8 N·m) 30V 290g CAN

XQ-POWER XQ-S9080FC
100 kg·cm peak stall torque at 30 V · 0.16 s/60° · 290 g · CAN CAN, 500–2500 µs position scale
Brushless motor, steel gears, 6 ball bearings, CNC aluminium case
54 × 25 × 96 mm · splash-proof, customizable

Need a different torque, travel or connector? The engineering team answers against your numbers.

XQ-S9080FC — the 100 kg·cm (9.8 N·m) column with a CAN node in place of the pulse input A brushless motor drives a steel train onto a 25T, φ7.96 mm output in six ball bearings, inside a 54 × 25 × 96 mm machined aluminium column, 290 g with the 7075 arm. The input stage is a CAN node: the command arrives as a frame from the bus master and the joint goes where the frame says. Nothing in the mechanics changed to make that possible.

The unit gives 75 kg·cm on 24 V, 90 kg·cm on 28 V and 100 kg·cm on 30 V, with speed and current at all three rails. Inspection sheet X9_9080.01, dated 2026-11-02, is the document this page is written from.

Peak stall torque100 kg·cmat 30 V · 1388.7 oz-in · 9.8 N·m Speed0.16 s/60°at 30 V · 0.28 s at 24 V Supply24–30 Vthree published points
ControlCANCAN bus · ±100° on the command scale Envelope54 × 25 × 96 mm74.0 mm across the ears · 25T-φ7.96 Mass290 g6 ball bearings · no mechanical stop

Is the XQ-S9080FC the right servo for your joint?

A hundred kg·cm held in 290 g is a case and bearing problem, and those parts are unchanged here. What the CAN input adds is a place in a network: the master addresses this joint, decides when the frame goes out, and knows from the arbitration identifier how late that frame can be. On an axis that has to hold a relationship with a second axis, that bounded latency is the reason to pick this build.

Travel is ±100° mapped across the 1000–2000 µs span the sheet publishes, with the limit field at 3-4 left blank. The machine owns its hard stops. Section 5-5 marks the degree customizable, so a narrower working range is a setting.

Specify this unit when

  • The machine already runs a CAN bus and the master addresses nodes
  • Two or more joints have to hold a relationship inside a bounded window
  • Travel inside ±100° covers the move
  • The rail holds 24–30 V under load
  • The harness can be built to a J30J-9TJL connector

Specify a different unit when

  • The controller has no CAN port and no gateway in front of it
  • The joint finds its position on an internal stop
  • The machine runs a 6–8.4 V rail
  • The joint needs more than 100 kg·cm at 30 V
  • The bay cannot take a 54 mm wide case

Torque and speed at 24, 28 and 30 Volts

Locked-shaft torque, no-load speed, no-load current and stall current from rows 4-1 to 4-13. The network changes where the command comes from. It does not change a single number in this table.

Supply Peak stall torque No-load speed No-load current Stall current
24 V 75.0 kg·cm 0.28 s/60° 150 mA under 2 A
28 V 90.0 kg·cm 0.20 s/60° 180 mA under 2.5 A
30 V 100.0 kg·cm 0.16 s/60° 200 mA under 3 A

100 kg·cm at 30 V with 0.16 s per 60°; 90 kg·cm at 28 V and 75 kg·cm at 24 V. Speed more than halves across the rail, 0.28 s down to 0.16 s, so the supply belongs in the joint specification.

Stall current is published as a ceiling: under 2 A at 24 V, under 2.5 A at 28 V, under 3 A at 30 V, against 150 to 200 mA at no load. On a bus the ceilings add up. Six of these at 30 V is under 18 A on one feed before anything else on the machine is counted.

Fit: envelope, spline and mass

54 × 25 × 96 mm, 74.0 mm across the mounting ears, 4.0 mm of ear thickness. The ears sit at the top of the column so the bracket takes the load in shear next to the output and the body hangs below. Check the clearance under the case before the plate is cut.

25T at φ7.96 mm, with a 7075 aluminium arm in the box. That is a heavy spline for a 290 g unit and it is what lets the output take 100 kg·cm without an outboard support on the arm.

290 g including the arm. On a moving gantry that mass is what the rest of the axis accelerates, and this frame is the lightest way we build 100 kg·cm at 30 V.

Drive, current and heat

Under 3 A at stall on 30 V, 200 mA at no load. The current is low for the torque because the rail is high, which puts the supply in charge of what the joint delivers: a feed that sags to 26 V under load moves the joint into the 28 V column and 90 kg·cm.

Dead band 3 µs, neutral 1500 µs, window 500–2500 µs, all marked customizable. On a bus those figures become the smallest position step the master can ask for and the point the joint treats as centre, so they belong in the commissioning notes along with the node address.

The case is a machined column with fins over the motor section, and 3 A does not heat a body this size in any ordinary duty. The joint that heats is the one holding a load against gravity with the arm stationary: current stays near stall and the fins carry everything away.

Six bearings on the output let the arm run without outboard support. Where the arm is long enough to whip, add the support: bearings carry torque, and a bending moment at the end of a lever is a different load.

Sealing and environment

Section 3-11 of the inspection sheet records splash resistance as Yes. The case is a single machined billet with the joint faces sealed, which is what a wash-down bay or an outdoor enclosure asks for. A higher water-protection grade is built to order.

The connector at the base of the column is outside the sealed volume. Keep the J30J mating plug dry, or seal it to the same standard as the case, and run the lead down and away from the entry so water runs off the joint.

We rate the unit −30 ℃ to 65 ℃ operating and −30 ℃ to 70 ℃ storage. The top of that range interacts with the thermal note above: a joint already working near its limit at 25 ℃ has nothing left in reserve at 55 ℃.

Full specification

The complete sheet for the XQ-S9080FC, in the order it appears on inspection document X9_9080.01, dated 2026-11-02: measured figures throughout, and where we have none the row says so.

Model XQ-S9080FC
Peak stall torque (SI) 9.8 N·m at 30 V
Voltage range 24–30 V
Control interface CAN bus
Amplifier Digital controller
Rotating direction CCW (1000–2000 µs), customizable
Angle of limit None, no mechanical stop
Motor Brushless
Gear train Steel
Bearing system 6 ball bearings
Output spline 25T, φ7.96 mm
Horn supplied 7075 aluminium CNC arm supplied
Case Aluminium CNC, all-metal case
Dimensions 54 × 25 × 96 mm
Weight 290 g
Cable length J30J-9TJL connector, lead purchased separately
Operating temperature −30 ℃ to 65 ℃
Storage temperature −30 ℃ to 70 ℃
Sealing Splash-proof · higher water-protection grade built to order
Specification revision X9_9080.01, dated 2026-11-02

Download the XQ-S9080FC datasheet (PDF)

The inspection sheet for this model, including the dimensional drawing and the control-signal table, is available as a PDF.

XQ-S9080FC inspection specification
Revision X9_9080.01 · dated 2026-11-02 · PDF
Download PDF

If you need the drawing in DWG, a STEP model, or the control-signal table as a separate sheet, tell us which format your CAD system uses and we will send that instead.

Variants, samples and OEM work

The same mechanics with a pulse input is S9080F, and the RS485 version of this column is RS9080F. The next frame up carries 250 kg·cm as S9200DC.

PWM, CAN and RS485 builds of this frame share the bracket pattern, the arm and the travel figures, so a machine specified on one interface moves to another without redrawing the mount. Tell us the interface at the quotation stage and the harness is built to it.

For OEM and ODM work on the XQ-S9080FC we start from five numbers: the torque you need at your speed, the supply you actually run, the interface your controller speaks, the envelope the joint allows, and the duty cycle. Send those and we answer one of three ways — the XQ-S9080FC covers it as stock at 100 kg·cm, a build of the same 54 × 25 × 96 mm frame does, or the axis needs a different frame. Send the XQ-S9080FC numbers to the engineering team.

Quick facts and cross-reference

The rows below are what to quote for the XQ-S9080FC: 100 kg·cm (9.8 N·m) on 24–30 V with CAN input, plus the two makes buyers usually weigh it against.

Model XQ-S9080FC
Peak stall torque 100 kg·cm · 9.8 N·m at 30 V
Voltage range 24–30 V
Control interface CAN bus
Speed 0.16 s/60°
Mass / envelope 290 g · 54 × 25 × 96 mm
Also described as CAN bus servo, CAN actuator, CANopen servo, robot joint actuator

Buyers often arrive here from a Waveshare RSBL120-24 or a Feetech SM160BL, which are built around 12-24 V bus rails with an onboard driver; the XQ-S9080FC is 100 kg·cm (9.8 N·m) on 24–30 V, so put the two on the same rail and in the same unit before comparing torque.

Cross-reference Waveshare RSBL120-24, Feetech SM160BL
Their typical rail built around 12-24 V bus rails with an onboard driver
This model 100 kg·cm (9.8 N·m) on 24–30 V, CAN input

FAQ

What baud rate and node ID does the S9080FC ship with?

The inspection sheet specifies the command signal as CAN and stops there. Baud rate, node identifier and the frame layout are set at order stage against your master, written into the protocol note that ships with the unit, and confirmed in writing before the order is accepted.

Is the lead included?

No. The unit carries a J30J-9TJL connector and the mating lead is a separate purchase. Give us the length and the pinout the controller expects and the harness is quoted with the servo.

Does the joint have a mechanical stop?

No. Section 3-4 is blank and section 5-5 gives ±100° of running degree across the 1000–2000 µs span. The machine provides its own hard stops, and the servo drives to whatever the master asks for.

What supply does it need?

24 to 30 V, and the joint is specified on the rail it actually sees. At 28 V it gives 90 kg·cm at 0.20 s; at 30 V, 100 kg·cm at 0.16 s. A feed that sags under load drops the joint into a lower column.

I have the PWM build on the machine. Can I move the axis to CAN?

Yes. The bracket pattern, the 25T φ7.96 mm output, the 290 g mass and the ±100° travel are the same on both builds, so the mount and the arm stay. Only the harness and the controller configuration change.

How much current should I budget per node?

Budget the ceiling at the rail you run: under 3 A at 30 V, under 2.5 A at 28 V, under 2 A at 24 V, plus 200 mA at no load. Size the feed on the number of nodes that can stall at the same moment.

Is the XQ-S9080FC a drop-in replacement for a Waveshare RSBL120-24?

No. The Waveshare RSBL120-24 runs on a different rail and a different frame, while the XQ-S9080FC is 100 kg·cm (9.8 N·m) on 24–30 V with CAN input, so a swap means checking voltage, envelope and travel first. Send the rail and envelope your machine runs and we will say whether the XQ-S9080FC frame fits.

What should I compare before choosing between the XQ-S9080FC and a Feetech SM160BL?

Four numbers decide between the XQ-S9080FC and a Feetech SM160BL: peak stall torque in N·m, the rail you actually run, stall current, and whether your controller speaks CAN. The XQ-S9080FC publishes 100 kg·cm (9.8 N·m) on 24–30 V; put the Feetech SM160BL on that same rail and in the same unit before you compare the two.

Model

XQ-S9080FC

Motor

Brushless

Gear train

Steel

Bearings

6 ball bearings

Torque @ 30 V

100.0 kg·cm (1388.7 oz-in)

Torque @ 28 V

90.0 kg·cm (1249.9 oz-in)

Torque @ 24 V

75.0 kg·cm (1041.6 oz-in)

Speed @ 30 V

0.16 s/60°

Speed @ 28 V

0.20 s/60°

Speed @ 24 V

0.28 s/60°

Voltage range

24–30 V

Dimensions

54 × 25 × 96 mm

Weight

290 g

Output spline

25T, φ7.96 mm

Case

CNC aluminium case

Protection

Splash-proof, customizable

Communication

CAN

Request a quote for Industrial Brushless Servo S9080FC 100kg (9.8 N·m) 30V 290g CAN
















    Scroll to Top