, , ,

Heavy Duty Brushless Servo RS8185HV 85kg (8.3 N·m) 16.8V 92g RS485

XQ-POWER XQ-RS8185HV
85 kg·cm peak stall torque at 16.8 V · 0.11 s/60° · 92 g · RS485 800–2200 µs, neutral 1500 µs
Brushless motor, stainless steel gears, 2 ball bearings, CNC aluminium case
40 × 20 × 44 mm · splash-proof, customizable

Need a different torque, travel or connector? The engineering team answers against your numbers.

XQ-RS8185HV — 85 kg·cm (8.3 N·m) on 16.8 V over a two-wire RS485 line, for a joint at the far end of the machine A brushless motor drives a stainless steel train onto a 25T, φ7.96 mm output carried in two ball bearings, inside a 40 × 20 × 44 mm machined aluminium case at 92 g. The winding is set for a 4S pack: the unit peaks on 16.8 V where the 2S build of this frame peaks on 8.4 V.

The unit gives 42 kg·cm on 8.4 V, 60 kg·cm on 12.0 V and 85 kg·cm on 16.8 V, with speed and current at all three rails. Rated and tested to inspection sheet X8_8185.01, dated 2025-07-01.

Peak stall torque85 kg·cmat 16.8 V · 1180.4 oz-in · 8.3 N·m Speed0.11 s/60°at 16.8 V · 0.17 s at 8.4 V Supply8.4–16.8 Vthree published points
ControlRS485RS485 · 360° on the command scale Envelope40 × 20 × 44 mm54.0 mm across the ears · 25T-φ7.96 Mass92 g2 ball bearings · no mechanical stop

Is the XQ-RS8185HV the right servo for your joint?

A differential pair is the reason this build exists. Where the joint hangs at one end of a 4S machine and the controller sits at the other, a twisted pair carries the command past the motor cables without picking up what they radiate. The transceiver is inside the case and the cable is ordinary twisted pair.

The shell is the 40 × 20 × 44 mm case at 92 g: two bearings on a 25T φ7.96 mm output, ears cut into the sides, 360° of running degree across the 1000–2000 µs span, and no stop anywhere inside. Section 5-1 names RS485 as the command signal.

Specify this unit when

  • The controller or a converter speaks RS485 over twisted pair
  • The cabinet is some distance from the joint
  • The machine runs a 4S pack and holds about 16.8 V under load
  • The pocket is 20 mm deep and 44 mm tall
  • The joint can use a 25T, φ7.96 mm spline

Specify a different unit when

  • There is no RS485 port and no converter on the machine
  • The machine runs a 2S pack, where this build gives 42 kg·cm
  • The joint depends on an internal stop for its end positions
  • The arm carries its load a long way out from the spline
  • The bay cannot take 54 mm across the ears

Torque and speed at 8.4, 12.0 and 16.8 Volts

Locked-shaft torque, no-load speed, no-load current and stall current from rows 4-1 to 4-13. Read the left column against the pack in the machine: the same joint gives 42 kg·cm on a 2S rail.

Supply Peak stall torque No-load speed No-load current Stall current
8.4 V 42.0 kg·cm 0.17 s/60° 320 mA 4.0 A
12.0 V 60.0 kg·cm 0.14 s/60° 370 mA 5.0 A
16.8 V 85.0 kg·cm 0.11 s/60° 440 mA 6.0 A

85 kg·cm at 16.8 V with 0.11 s per 60°, 60 kg·cm at 12.0 V, 42 kg·cm at 8.4 V. The whole spread lives between the rails, so the pack is part of the joint specification: a 4S pack that sags to 13 V under load hands the joint the 12 V column at 60 kg·cm.

Stall current is 4.0 A at 8.4 V, 5 A at 12.0 V and 6.0 A at 16.8 V, against 320 to 440 mA at no load. The 300 mm lead carries all of it, and on a 4S machine the supply and the connector are the parts that decide whether the joint ever sees 16.8 V under load.

Fit: envelope, spline and mass

40 × 20 × 44 mm, 54.0 mm across the mounting ears, 49.4 mm to the top of the spline. Same envelope as the 2S build of this frame, so a pocket cut for one takes the other: measure from the ear face, because the mounting face sits at the top of the fins.

25T at φ7.96 mm with a 7075 aluminium arm in the box. This is the spline the 25, 45, 75 and 85 kg·cm frames of the series share, so an arm cut for any of them seats here.

92 g with the arm. The high-voltage winding does not add mass: the difference between this build and the 2S one is copper and turns.

Drive, current and heat

6.0 A at stall on 16.8 V and 440 mA at no load. The current is the same figure the 2S build reaches at 8.4 V, so the lead and the connector are sized the same way; what changes is the voltage the insulation and the supply have to hold.

Dead band 2 µs, neutral 1500 µs, window 800–2200 µs, all marked customizable. That 2 µs band is tighter than the 3 µs on the 9-series frames, which matters on a linkage that has to hold a position against a spring.

The case is a machined block with fins over the motor section, and the drive sits against them. A joint holding a load against gravity with the arm stationary pulls near stall current and has only the fins and the bracket to shed the heat.

Two bearings carry the torque at 85 kg·cm without trouble. They do not resist a bending moment, so keep the load close to the spline or support the far end of the arm.

Sealing and environment

Section 3-11 records splash resistance as Yes on a machined aluminium case with sealed joint faces. A higher water-protection grade is built to order, with the class and the test standard agreed at order stage.

The lead leaves through a sealed exit at the base of the case and the connector on its end sits outside that seal. Keep the plug dry or seal it to the same standard, and dress the lead downward from the exit.

We rate the unit −15 ℃ to 65 ℃ operating and −20 ℃ to 70 ℃ storage. The cold end is narrower than the 9-series frames carry, so a machine that works outdoors in winter should check it before the joint is specified.

Full specification

The complete sheet for the XQ-RS8185HV, in the order it appears on inspection document X8_8185.01, dated 2025-07-01: measured figures throughout, and where we have none the row says so.

Model XQ-RS8185HV
Peak stall torque (SI) 8.3 N·m at 16.8 V
Voltage range 8.4–16.8 V
Control interface RS485
Amplifier Digital controller
Rotating direction CCW (1000–2000 µs), customizable
Angle of limit None, no mechanical stop
Motor Brushless
Gear train Stainless steel
Bearing system 2 ball bearings
Output spline 25T, φ7.96 mm
Horn supplied 7075 aluminium CNC arm supplied
Case Aluminium CNC, all-metal case
Dimensions 40 × 20 × 44 mm
Weight 92 g
Cable length 300 mm lead fitted
Operating temperature −15 ℃ to 65 ℃
Storage temperature −20 ℃ to 70 ℃
Sealing Splash-proof · higher water-protection grade built to order
Specification revision X8_8185.01, dated 2025-07-01

Download the XQ-RS8185HV datasheet (PDF)

The inspection sheet for this model, including the dimensional drawing and the control-signal table, is available as a PDF.

XQ-RS8185HV inspection specification
Revision X8_8185.01 · dated 2025-07-01 · PDF
Download PDF

If you need the drawing in DWG, a STEP model, or the control-signal table as a separate sheet, tell us which format your CAD system uses and we will send that instead.

Variants, samples and OEM work

The RS485 build on the 2S winding is RS8185D, and the pulse and CAN builds of this winding are BLS8185HV and BLS8185HVC. The 48 kg·cm frame in the same tab pattern is BLS8145D.

This case is offered with a pulse input, a CAN node and an RS485 transceiver on both windings. A machine that moves between them keeps the bracket, the arm and the travel figures and changes only the harness and the pack.

For OEM and ODM work on the XQ-RS8185HV we start from five numbers: the torque you need at your speed, the supply you actually run, the interface your controller speaks, the envelope the joint allows, and the duty cycle. Send those and we answer one of three ways — the XQ-RS8185HV covers it as stock at 85 kg·cm, a build of the same 40 × 20 × 44 mm frame does, or the axis needs a different frame. Send the XQ-RS8185HV numbers to the engineering team.

Quick facts and cross-reference

The rows below are what to quote for the XQ-RS8185HV: 85 kg·cm (8.3 N·m) on 8.4–16.8 V with RS485 input, plus the two makes buyers usually weigh it against.

Model XQ-RS8185HV
Peak stall torque 85 kg·cm · 8.3 N·m at 16.8 V
Voltage range 8.4–16.8 V
Control interface RS485
Speed 0.11 s/60°
Mass / envelope 92 g · 40 × 20 × 44 mm
Also described as RS485 servo, Modbus servo, RS-485 bus actuator, daisy-chain actuator

Buyers often arrive here from a Hitec D980TW or a Feetech FT5335M, which are built around 6.0-8.4 V receiver rails with PWM input; the XQ-RS8185HV is 85 kg·cm (8.3 N·m) on 8.4–16.8 V, so put the two on the same rail and in the same unit before comparing torque.

Cross-reference Hitec D980TW, Feetech FT5335M
Their typical rail built around 6.0-8.4 V receiver rails with PWM input
This model 85 kg·cm (8.3 N·m) on 8.4–16.8 V, RS485 input

FAQ

What is the difference between the HV build and the 8.4 V build of this frame?

The winding. The case, the 25T φ7.96 mm output, the two bearings, the arm and the 360° figure are the same parts. This build peaks at 85 kg·cm on 16.8 V; the 8.4 V build peaks at 85 kg·cm on 8.4 V and gives 42 kg·cm if you put 8.4 V into this one. Choose by the pack in the machine.

Does it have a mechanical stop?

No. Section 3-4 reads No Limit and 5-5 gives 360° across the 1000–2000 µs span. The machine provides the end positions, and at 85 kg·cm a joint driven into a hard stop damages the linkage.

How much current does it draw?

4.0 A at 8.4 V stall, 5 A at 12.0 V and 6.0 A at 16.8 V, with 320 to 440 mA at no load. Size the supply, the switch and the connector on the 6 A figure at the rail you run.

Can I run it on 5S?

Section 4-1 to 4-13 give three working points and 16.8 V is the top of them. We do not publish a figure above that, so a 5S pack is outside what this sheet supports; tell us the rail and we will say what we can offer.

Does the RS8185HV speak Modbus?

Section 5-1 of the inspection sheet names RS485 for this model and nothing above it. The frame layout and command set are ours, documented in the protocol note that ships with the unit and agreed with you before the order. Where the master needs Modbus RTU, tell us at quotation and we quote the frame that carries it.

How long a run will it take?

The limit is the transceiver at the master and what the pair runs beside. Keep it clear of the motor cables, terminate at both physical ends, leave the middle drops open, and check the line with the last joint connected.

Is the XQ-RS8185HV a drop-in replacement for a Hitec D980TW?

No. The Hitec D980TW runs on a different rail and a different frame, while the XQ-RS8185HV is 85 kg·cm (8.3 N·m) on 8.4–16.8 V with RS485 input, so a swap means checking voltage, envelope and travel first. Send the rail and envelope your machine runs and we will say whether the XQ-RS8185HV frame fits.

What should I compare before choosing between the XQ-RS8185HV and a Feetech FT5335M?

Four numbers decide between the XQ-RS8185HV and a Feetech FT5335M: peak stall torque in N·m, the rail you actually run, stall current, and whether your controller speaks RS485. The XQ-RS8185HV publishes 85 kg·cm (8.3 N·m) on 8.4–16.8 V; put the Feetech FT5335M on that same rail and in the same unit before you compare the two.

Model

XQ-RS8185HV

Motor

Brushless

Gear train

Stainless steel

Bearings

2 ball bearings

Torque @ 16.8 V

85.0 kg·cm (1180.4 oz-in)

Torque @ 12.0 V

60.0 kg·cm (833.2 oz-in)

Torque @ 8.4 V

42.0 kg·cm (583.3 oz-in)

Speed @ 16.8 V

0.11 s/60°

Speed @ 12.0 V

0.14 s/60°

Speed @ 8.4 V

0.17 s/60°

Voltage range

8.4–16.8 V

Dimensions

40 × 20 × 44 mm

Weight

92 g

Output spline

25T, φ7.96 mm

Case

CNC aluminium case

Protection

Splash-proof, customizable

Communication

RS485

Request a quote for Heavy Duty Brushless Servo RS8185HV 85kg (8.3 N·m) 16.8V 92g RS485
















    Scroll to Top